How to set digital cable programs and channels

The company NKTV provides the ability to view not only analog but also digital channels if your TV has a standard tuner DVB-C - you can set and watch them for free. In this article we will look at ways of tuning digital cable channels NCTV on different TV models. 

I Want to remind you that the company NCTW I have nothing to do, the information is purely informative in nature to help the cable TV operator. Phone companies NCTV: 1569 or 47-09-42, here there and direct your questions ab

a List of digital cable channels (open and paid) you can take on our file sharing section: lists

Digital cable programs and channels

Basic settings to receive digital package of channels "Outdoor" on Your TV:
- symbol rate: 7000
- QAM: 64
- the frequency at which the open broadcast channels(MHz): 210, 362, 370, 378, 386, 394, 434, 450, 458, 786, 810, 818

Settings to receive digital package of channels "HD" on Your TV:
- symbol rate: 7000
- QAM: 256 (07-10-2013 this parameter changed from 64 to 256)
- Frequency at which broadcast of the open HD channels (MHz): 802

setting up digital cable programs or channels on the SAMSUNG TV

Setting up digital cable programs or channels on SAMSUNG TV
- Go to the menu and select the Channel (picture a satellite dish).
- Select Country.
- For analog and digital channels, specify the "Other." the
- Return to previous section and select Cable search options".
- Customizable settings of the "Frequency start"- 362000, "Frequency end"-818000, "Modulation"-QAM64 and "transfer Rate"- 7000. the
- Return to previous section and select the item "auto".
- Selectable signal source - Cable".
- In the new window auto-tuning select the Digital (if you don't want to wait long enough to tune analogue channels).
- using the down and up buttons to select search mode "Full" and press ENTER. Then start channel search and will be completed in about 15-30 minutes.

setting up digital cable programs or channels on LG TV

setting up digital cable programs or channels on the LG TV
- Press the Menu button on the remote control, select the tab "OPTIONS".
- Next, choose the country Finland, Germania on a new TV, you can choose, and Russia.
- Next select the tab "SETTINGS".
- Select "AUTO search". In it, select "CABLE".
- Next manually put the frequency -based one mentioned above), Speed - 7000, Modulation - QAM-64.
- Next, close this window and click "OK".
- click to PERFORM.
- TV configures all channels are digital first and then analog.

setting up digital cable programs or channels on PHILIPS TV

setting up digital cable programs or channels on your TV PHILIPS
- Press on the remote control button "House" and get into the menu.
- Choose "Configuration".
- "Install".
- "channel Settings".
- "Automatic installation".
- "Start".
- "Reset channels".
- "Finland" "Norway". The selection of countries is needed to activate the menu cable TV because formal parameters for the cable in the Ukraine and Russia are not standardized.
- "cable". If this menu item does not, then either you have chosen a country without digital cable, or your TV does not contain a DVB-C receiver.
- "Install". Do not start the search! First, "Installation"!
- speed Mode transmission "Manual".
- transfer Speed -7000
- Scanning frequency. "Quick scan". You can leave "Full scan, with the following two step to skip. But keep in mind that a full scan takes about half an hour!
- power frequency – to "Manual."
- Network frequency – (one of the above)
- Analogue channels – "On". Otherwise there will be only found digital channels.
- Finish .
- Run the search Start .
- Waiting for a completed search.
- when the search finishes, click "Finish" .
- you can Now exit the menu, press "BACK" or "TV" and start watching the channels.

setting up digital cable programs or channels on the SONY TV

setting up digital cable programs or channels on the SONY TV
- Push the "MENU" button, select "SETTINGS".
- In the window that opens, select the item "DIGITAL CONFIGURATION. By selecting this option, press the "OK" button.
- In the window that appears, select "DIGITAL SETTING".
Next select the item "AUTO scan DIGITAL STATIONS.
- Next to the question - "do you WANT to START AUTOMATIC SEARCH?" click "OK".
- In the dialog box, select "CABLE".
- In the dialog box, select "QUICK SCAN".
- Then, select "MANUAL".
- Next, enter the frequency (one of the above)
- the access Code to the network, leave the "AUTO". Next, enter symbol RATE 7000
- If input field change to 64 QAM and the search type "Network"
- After all passed, click "START".

Link to this story: http://en.rem-tv.net/publ/8-1-0-139

Add new comment

Гостевой

CAPTCHA на основе изображений
Enter the characters shown in the image.